
- Schick 33 sensor cdr dicom 5 install#
- Schick 33 sensor cdr dicom 5 update#
- Schick 33 sensor cdr dicom 5 upgrade#
- Schick 33 sensor cdr dicom 5 full#
- Schick 33 sensor cdr dicom 5 windows 10#
Verify in the Upgrade Utility that the Sensor Module Firmware Version is also up-to-date (the number will appear in green). Connect either the Elite or the Schick 33 Sensor to the Schick USB 2.0 Module.
if you update one computer to the 5.16 driver and update firmware/ FPGA of the module, for this module to be compatible in another room, it must be on the 5.16 driver.
NOTE: if this module is used in other rooms, you must update the resof the rooms to the same driver. If the Firmware Version of the sensor is not up-to-date (the number appears in red), select the button to upgrade the Firmware Version. Verify in the Upgrade Utility that the Sensor Module Firmware Version is also up-to-date (the number will appear in green). For the Schick Elite or Schick 33 Sensors the calibration files will install automatically when the software is launched.
NOTE: if this module is used in other rooms, you must update the rest of the rooms to the same driver. Once completed, select the FPGA button to update. If the Firmware and FPGA Versions are not up-to-date (the numbers appear in red), select the button to upgrade the Firmware Version first. Verify the Firmware Version and FPGA Versions for the USB Interface are up-to-date (the numbers will appear in green). Open the Upgrade Utility (Start | All Programs | CDR DICOM for Windows | Upgrade Utility). Once the installation is complete, plug the Schick USB 2.0 Module into the A-to-B USB Cable, and then the USB Cable into the back of the computer tower. Follow the prompts to install the driver. In the extracted folder, right-click the CDR Elite Setup and select Run as administrator. then right-click again and select Extract All. Once the folder has downloaded, right-click the folder and UNBLOCK. Download the Schick USB 2.0 Module driver from Schick's Website, Select the Schick 33 and Elite Sensor Drivers. There is a now an option on the Sensor Tab in the X-ray Acquisition Control Properties screen for Sensor Type, this shows what type of sensor is plugged into the remote box or USB module. NOTE: When the Fixed Enhancement is applied, the slider for the sharpness will be shown at the percentage set in this menu. Select the Mixed Mode option to apply to the image. Select the Sharpen % you would like to be applied to the image. This feature is only applied to Schick 33 Images. All of the enhancements are applied before you see the image and then can no longer be changed after the image appears in the software. When you do select this option you will no longer have use the Sharpen Slider, Diagnostic Tasks, and Enhancement Modes after the image is acquired into the software. Fixed enhancement is a new option under the Image tab on the X-ray Acquisition Control Properties Screen. Right-click on the Image | Enhancement | select Mode A or Mode B: This feature, which is always available to Schick 33 customers, has been updated to offer an additional selection. One of the advantages of dynamic image enhancement is the ability to adjust the amount of sharpness in an image after it is acquired. Two New Image Enhancement Features have been added to CDR 5.14 – Enhancement Mode and Fixed Enhancement 8GB RAM (minimum) / 16 GB RAM (recommended). TCP/IP Networking Protocols (for DICOM Servers). Windows Server 2008 R2, Windows Server 2012 R2, Windows 10 Pro (64 bit), Windows 8.1 Pro or Windows 7 Pro (64 bit).500 GB hard drive (practice-specific, depends on number of patients).4GB Video graphics card – NVidia or ATI recommended.Windows 10 Pro, Windows 8 Pro or Windows 7.
The server software only needs to be installed if the server machine is new or if a full reinstallation of the server is in progress.ĬDR Dicom 5.14 has the same features as CDR 5.11, the main difference between the two is that CDR 5.14 is now Windows 10 compatible. **Please note if an office is already using CDR Dicom 5.4 or 5.11, the client portion of the updated version will only need to be installed on the server (if it has the client software installed) and each workstation.